VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Vape Cartridge  /  Vape Cartridge session and puff count for the EU market
vape cartridges · brand owners

Vape Cartridge session and puff count for the EU market

Vape Cartridge is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Published 22 February 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.

The checks behind every shipment

Buyers come to us for vape cartridge after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for brand owners.

7 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

Where the margin really sits

We publish a realistic band of 1.81 to 5.33 per unit for standard configurations at 300 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

For brand owners, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Keeping the second shipment identical

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

  • Private label files archived for future rebrands
  • Specification locked in writing before production starts
  • Artwork proof plus physical dummy for custom packaging
  • Document pack prepared per destination market
  • Batch codes traceable from carton back to production date
  • Seven-day defect reporting with replace-or-credit

Compliance without the last-minute scramble

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

We keep batch codes traceable from carton to production date. When a market authority asks for traceability, a supplier who cannot produce it in an hour becomes a liability very quickly.

Specification summary

Typical specification for this category
Volume0.5 ml
CoreCeramic
Resistance1.5 ohm
Thread510 thread
AirflowSide
PackagingBlister
Minimum order300 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

What documents come with a shipment?

Commercial invoice, packing list, and the certificate pack for your market: test reports, declaration of conformity and safety data sheets. We send scans before dispatch so your broker can pre-clear the file.

How long does production take?

Around 12 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for vape cartridge?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

Related reading

Need a quotation on vape cartridges?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on vape cartridges

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us